"To Do" list

Major page changes a work in progress, come back (much) later!

Nb. "tbd" - to be decided, "dtf" - details to follow

Work in Progress

•  V-berth refit
•  Strip out old headlining
•  Clean up internal surfaces
•  Insulate throughout
•  Make and fit plywood lining panels
•  Trim out linings
•  Prepare all areas previously lined with vinyl for painting
•  Paint those areas
•  Make and fit new lockers & shelving
•  Fit supporting framework using utile hardwood from stock
•  Measure and cut (first cut or finished as appropriate) ply locker facings etc.
•  Veneer ply with "tiger stripe" Sapele veneer
•  Finish cut locker fronts, doors etc.
•  Fit and finish
•  Varnish
•  Electrics
•  Install 240v sockets in port and starboard shelves
•  Install 12v USB sockets ditto
•  Install 2x reading lights and 1x overhead light (white/red swtichable)
•  Prepare and varnish existing wood finish areas
•  Prepare and paint (or otherwise improve) sole
•  Make and fit deadlights for portholes
•  Make and fit insulated and uninsulated inserts for hatch
•  Refurbish wardrobe interior
•  Galley
•  Order parts needed to replace cooker
•  Remove existing cooker
•  Make and fit new fold away worktop
•  Make good old gimbal cutouts
•  Measure, make and fit new gimbal mounting pads
•  Fit replacement cooker
•  Gas leak test

Provisional full list  (this will be prioritised and rearranged!)

•  Heads
•  Remove and replace headlining
•  Replace tap/shower head
•  Repair / revise holding tank plumbing
•  Replace broken flish source selector valve
•  Install tank / overboard diverter valve
•  Cobble together means of pumping out tank to portable disposal tank
•  Solve problem of water leaking out into saloon when showering
•  Fit shelving in locker below sink
•  Replace or remove faulty light above mirror
•  Fit extractor fan to deck vent
•  Prepare and varnish all woodwork
•  Obscure porthole for privacy
•  Saloon
•  Deckhead
•  Insulation
•  Refurbish or replace headlining panels (tbd)
•  Remove and replace cabin side vinyl linings (dtf)
•  Repair / refurbish window internal frames
•  Consider improvements to overhead lockers
•  Repair and improve pull out double frame
•  Repair and improve slots and boards for sea berths
•  Replace saloon upholstery
•  Refurbish saloon hanging locker
•  Cabin Sole
•  Create storage compartments to either side of bilge
•  Remake or replace cabin sole plates to suit
• Rebuild companionway step to improve storage (safety gear &c.)
•  12v Electrical Supply
•  Batteries
•  Install secondary battery bank (non-essential - domestic &c.)
•  Make and fit new battery selector switch panel
•  Amend and replace mains and engine charging as appropriate
•  Solar
•  Install permanent solar panels on hatch garage and aft cabin deck
•  Fittings and wiring for deployable foldaway panels on cabin top
•  Charge controller(s) as appropriate
•  Wind
•  Fit wind turbine on mizzen mast
•  Wiring and control as required
•  Bower Anchor
•  Electric anchor windlass
•  Remove manual windlass and offer for sale
•  Run heavy duty cabling to location from new secondary battery bank
•  Install electric anchor windlass
•  New chain & rode
•  New best bower anchor
•  Investigate sealing chain locker from bilge and fitting dedicated drains

Pagan - First

•  Engine Bay
•  Install and plumb in Calorifier
•  Install engine bay fire extinguisher(s)
•  Install engine bay tube heater(s)
•  Engine
•  Screw fuel filter back to bulkhead!
•  Free off throttle cable
•  Fault find oil pressure and temperature gauges
•  Replace engine glow plugs with Fast-start type
•  Service engine
•  Cockpit locker hinges - fettle
•  Stanchion bases - fettle loose base, check rest
•  Starboard cockpit locker
•  Run pipework / ducting as necessary through to galley
•  Install 88l diesel tank
•  Make and fit shelf for fridge and freezer compressors
•  Relocate fresh water pump (to engine bay?)
•  Galley
•  Replace fridge compressor and evaporator plate
•  Oven Gimbal Lock
•  Gas detector
•  Kitchen roll holder
•  Fit and plumb in new tap
•  Heating
•  Run ducting to vents
•  Fit vents in forecabin, heads, saloon, cockpit and aft cabin
•  Install heater in port cockpit locker
•  Plumb in fuel supply
•  Install wiring harness
•  Commission & test heating system
•  Secure all ducting and lag joints
•  Heads
•  Install holding tank
•  Install fresh water flush tank
•  Install and plumb in tap / shower head
•  Fix leak(s) in deckhead above V-berth
•  Install TackTick NMEA interface and fluxgate compass
•  Install Tacktick mounting plates above chart table
•  Gash storage
•  Bilge pumps
•  Repair or replace manual bilge pump
•  Fit automatic electric bilge pump in engine bilge
•  Prevent routine water flow from engine bilge to main bilge (if necessary)
•  Fit larger automatic electric bilge pump in main bilge
•  Safety
•  Harness eyes
•  Fire extinguishers
•  Jacklines
•  Rig
•  Mizzen mast gate
•  Strengthen rigging attachments cockpit
•  Stbd aft lower chainplate crack
•  Remove and re-bed all chainplates
•  Repair crack aft of mast step
•  Replace standing rigging
•  Replace kicking strap
•  Genoa UV strip
•  Main & Mizzen Stack Packs
•  Repairs
•  Replace diesel filler deck fitting
•  Repair floor under saloon table
•  Replace engine hatch bolts
•  Re-bed and secure pulpit rail
•  Clean out bilges & inspect keel bolts
•  Sprayhood & cover windows
•  Replace bicolour on bow
•  Navigation
•  Replace AIS antenna
•  Replace main VHF antenna
•  Install new main VHF set
•  Install PA horn
•  Replace rail mount VHF antenna
•  Replace main mast antenna cables
•  Remove Cetrex autopilot inc. motor and chain drive
•  Install EV100 Wheelpilot
•  Replace main water tank
•  Remove old stainless tank
•  Measure up and order new plastic tank(s)
•  Install new tank(s)
•  Secure tank to prevent movement
• 
  

Pagan - Next

• 
  
•  Fit intake water strainer
•  Saloon cushions
•  Vent with fan above galley
•  Port cockpit locker
•  Petrol storage locker
•  Lead mainsail lines back to cockpit
•  Modify hatch garage coaming
•  Install turning blocks at mast base
•  Install deck organisers
•  Install clutch banks
•  Install winches on cabin top port & stbd
•  Dehumidifier
•  Saloon bookcase
•  TV system
•  Repair or replace cockpit duckboards
•  Revamp electrical system
•  Revise position &c of mains sockets
•  Install USB charging points as req.
•  Make new switch panel
•  Install tank gauges
•  Refurbish saloon sole plates

Pagan - Whenever

•  Replace cooker
•  Revamp saloon table
•  Refit aft cabin
•  Purchase inflatable sailing tender (DingyGO)

Done!

•  Lift out 2016
•  Remove rudder
•  Remove prop
•  Remove windvane
•  Replace Cutlass bearing
•  Fit PSS gland in place of stuffing box
•  Hull
•  Remove old antifoul (scrape or use a chemical stripper)
•  Make good any gelcoat damage etc
•  Repair crack at aft end of keel
•  Wet sand hull to a good finish
•  Apply two coats of Hempel High Protect epoxy
•  Apply one coat of Hempel light primer epoxy
•  Apply Hempel hard racing antifoul
•  Make good where windvane self steering was fitted
•  Refit stern tube
•  Refit shaft, cutlass bearing and Install PSS gland
•  Repitch prop
•  Refit prop
•  Refit rudder
•  Replace prop anode
•  Repaint topsides
•  Apply graphics and cove line
•  Paint boottop
•  Convert to Propane gas
•  Upgrade C80 software
•  Investigate source of fresh water in bilges

Boom Brake / Gybe Preventer